Clothes DryersWasher-Dryer Combo
GE Profile PFQ83HSSW Clothes Dryer Manual
Setup, everyday use, maintenance and troubleshooting for the 4.6 cu. ft. all-in-one washer-dryer, with verified specifications.
- Capacity4.6 cu. ft.
- TypeElectric, ventless
- CEF6 lb/kWh
About the GE Profile PFQ83HSSW
The GE Profile PFQ83HSSW is a 4.6 cu. ft. all-in-one washer-dryer certified under the ENERGY STAR program. It measures 28 in. wide, 46.7 in. high, and 32 in. deep.
As an all-in-one washer-dryer, it dries laundry in the same drum it washes in, using a heat pump to remove moisture without an exhaust duct.
Its combined energy factor (CEF) is 6 lb of clothes per kWh. That beats 47% of the 16 clothes dryers in our database.
Specifications
| Brand | GE Profile |
|---|---|
| Model number | PFQ83HSSW*** |
| Dryer type | Washer-Dryer Combo |
| Fuel | Electric |
| Venting | Ventless |
| Heat-pump technology | Heat Pump |
| Drum capacity | 4.6 cu. ft. |
| Width | 28.0 in. |
| Height | 46.7 in. |
| Depth | 32.0 in. |
| Combined energy factor (CEF) | 6.00 lb/kWh |
| Energy test cycle settings | Normal DRY (Sensor Dry Only) Eco Dry defaut off |
| Smart / connected features | No |
| Refrigerant | R-134a (GWP 1430) |
| ENERGY STAR Most Efficient | No |
Safety information
- Clean the lint filter before or after every load. Lint buildup restricts airflow, lengthens drying time and is a leading cause of dryer fires.
- Never dry items soiled with gasoline, solvents, cooking or massage oils, or other flammable substances — even after washing, residual oil can ignite. Do not dry foam rubber or rubber-backed items.
- Check inside the drum before every cycle; children and pets can climb in. Do not let children play on or in the dryer.
- Keep the area around the dryer free of lint, dust, paper and flammable products.
- Connect the unit to the electrical supply shown on its rating plate — some models of this type run on 120 V and others need a dedicated 240 V circuit. Do not use an extension cord or adapter.
Installation and first-time setup
This model is 28 in. wide, 46.7 in. high, and 32 in. deep according to the certification data. Add room behind it for the water hoses, drain hose and power cord, and in front for the door to open fully.
- Choose the location
Pick a solid, level floor within reach of hot and cold water valves, a drain standpipe and a suitable outlet, in a room that stays above freezing.
- Connect the power
Connect the unit to the electrical supply shown on its rating plate — some models of this type run on 120 V and others need a dedicated 240 V circuit. Do not use an extension cord or adapter.
- Connect water and drain
Connect the hot and cold fill hoses with new washers and route the drain hose to a standpipe with an air gap, exactly as for a washing machine. Remove all shipping bolts before the first run.
- Set up condensate removal
Route the drain hose to a standpipe, laundry tub or the washer drain as the instructions describe, or leave the water container in place and plan to empty it after every load.
- Level the dryer
Adjust the legs until the dryer is level side to side and front to back; a level drum tumbles evenly and runs quietly.
- Test run
Run a timed cycle with a few damp towels. Confirm that it heats and the drum turns smoothly, and that water drains or collects as expected.
Using your dryer
Loading
The 4.6 cu. ft. drum is sized for smaller loads — dry bulky items one at a time. Fill it loosely — clothes need room to tumble — and dry similar fabrics together so everything finishes at the same time. Clean the lint filter first.
Choosing a cycle
- Use automatic (sensor) cycles rather than timed drying whenever possible; they stop when clothes are dry instead of running a fixed time.
- Choose a lower heat setting for synthetics, activewear and delicates. Overdrying shrinks fabrics, sets wrinkles and wastes energy.
- Dry loads back to back so the dryer starts warm.
- The certified efficiency was measured on these settings: Normal DRY (Sensor Dry Only) Eco Dry defaut off. Using the same settings gives you results closest to the rating.
Living with a heat-pump dryer
- Expect longer cycles than with a vented dryer. Clothes also come out cooler, which can make them feel damp even when they are dry — check them after they have cooled for a minute.
- Clean the lint filter after every load and the secondary filter or condenser as often as the manual directs; ventless designs are very sensitive to lint.
- If the dryer collects water in a container rather than draining, empty it after every load.
- Run the washer's highest safe spin speed so less water reaches the dryer.
Using the combination unit
For wash-and-dry cycles, keep loads smaller than the maximum wash load so clothes can tumble dry evenly, and clean the lint filter as directed. Drying in an all-in-one takes longer than in a separate dryer.
Care and maintenance
| When | What to do |
|---|---|
| Every load | Clean the lint filter. Empty the water container if your model collects condensate. |
| Every month | Check whether water pools on the lint screen when you run tap water over it. If it does, wash the screen in warm, soapy water with a soft brush — dryer-sheet residue clogs the mesh. |
| Every 3 months | Wipe the moisture-sensor strips inside the drum (usually near the lint filter) with a soft cloth; residue makes the dryer stop too early or run too long. |
| As the manual directs | Clean the secondary filter, heat exchanger or condenser. On models with a removable condenser, rinse it under running water; on heat-pump models, follow the manual — fins can be easily damaged. |
| As needed | Remove ink, crayon or gum residue from the drum with a damp cloth and mild cleaner, then tumble a load of old rags to pick up anything left. |
Troubleshooting
Most dryer problems come back to airflow. Work through the checks below before calling for service; if the display shows a code, look it up in the code table in your manufacturer's manual.
| Problem | Possible cause | What to try |
|---|---|---|
| Takes too long to dry | Clogged lint filter or condenser; overloading; clothes very wet from the washer; full water container. | Clean all filters, dry smaller loads, use a higher washer spin speed and empty or check the drain. |
| No heat | Tripped breaker (on 240 V models, possibly one leg of a double breaker); heat cut out by a safety device after restricted airflow. (Heat-pump dryers run cooler by design.) | Reset the breaker fully off and on. If the drum turns but never heats, clean the lint path and call a technician. |
| Will not start | Door not fully closed; Start not held long enough; control lock on; tripped breaker or unplugged. | Close the door firmly, press and hold Start, turn off the lock and check the power supply. |
| Clothes too hot or shrinking | Heat setting too high; timed cycle too long; restricted airflow. | Use sensor cycles and a lower heat setting; clean the lint path. |
| Thumping, rattling or squealing | Coins, zippers or shoes in the drum; worn drum rollers, belt or glides. | Check pockets and the drum. Persistent squealing or thumping from an empty drum needs service. |
| Burning smell | Normal for the first uses of a new dryer; lint buildup near the heat source. | A faint smell during the first few loads is normal. Otherwise stop the dryer, clean the lint filter and housing, and call a technician if the smell continues. |
| Clothes wrinkled | Overloading; clothes left in the drum after the cycle. | Dry smaller loads, remove clothes promptly. |
| Clothes still damp after wash-and-dry | Load too large to dry in the same drum; lint filter clogged. | Reduce the load to the drying limit in the manual and clean the filter. |
| Water on the floor or container-full alert | Water container full or not seated; drain hose kinked or out of the standpipe. | Empty and reseat the container; check the drain hose routing. |
Frequently asked questions
What is the drum capacity of the GE Profile PFQ83HSSW?
The GE Profile PFQ83HSSW has a 4.6 cubic-foot drum in a cabinet 28 in. wide.
Does the GE Profile PFQ83HSSW need an outside vent?
No. It is a ventless heat-pump design: moisture is condensed into water that drains away or collects in a container, so no exhaust duct is needed.
Is the GE Profile PFQ83HSSW gas or electric?
It is electric. Check the rating plate for the voltage — some models of this type run on 120 V, others need a dedicated 240 V circuit.
What is the CEF rating of the GE Profile PFQ83HSSW?
Its combined energy factor is 6 lb/kWh — the pounds of clothes it dries per kWh of energy. Higher numbers mean a more efficient dryer.
Is there a matching ENERGY STAR washer for the GE Profile PFQ83HSSW?
The certification record does not list a paired ENERGY STAR washer for this dryer.
Is the GE Profile PFQ83HSSW ENERGY STAR certified?
Yes. It appears on the ENERGY STAR certified clothes dryers list, with a certification date of July 2024.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified clothes dryers dataset published by the U.S. Environmental Protection Agency (record certified July 1, 2024), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with GE Profile. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact GE Profile or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.