LED DownlightsRecessed
Adetu LBT-3/9XDPL-18 LED Downlight Manual
Setup, everyday use, maintenance and troubleshooting for the 9 in. recessed LED downlight, with verified specifications.
- Light output1,480 lumens
- Power18 W
- Efficacy82.2 lm/W
- Color temp.2700–5000K (selectable)
About the Adetu LBT-3/9XDPL-18
The Adetu LBT-3/9XDPL-18 is a 9 in. recessed LED downlight certified under the ENERGY STAR program for light fixtures. It produces 1,480 lumens from 18 W of input power, an efficacy of 82.2 lumens per watt. That efficacy is better than 19% of the 3,089 Recessed models in our database.
Light quality: the fixture offers selectable color temperatures of 2700K, 3000K, 3500K, 4000K, or 5000K and a color rendering index of 88.
Notable features include continuous dimming, a damp-location rating, and an IC rating for direct contact with ceiling insulation. The rated light-source life is 72,000 hours.
Specifications
| Brand | Adetu |
|---|---|
| Model number | LBT-3/9XDPL-18 |
| Model name / series | Surface mounted led ceiling light |
| Fixture type | Recessed |
| Nominal size / aperture | 9 in. |
| Light output | 1,480 lumens |
| Input power | 18.0 W |
| Efficacy | 82.2 lm/W |
| Color temperature(s) | 2700K, 3000K, 3500K, 4000K, 5000K |
| Color rendering index (CRI) | 88 |
| Rated light-source life | 72,000 hours |
| Power factor | 0.92 |
| Continuously dimmable | Yes |
| Location rating | Damp location |
| Indoor / outdoor use | Indoor |
| Insulation contact rating | IC |
| Airtight rated | No |
| Tunable / selectable white | Yes |
| Full-color tunable | No |
| Selectable light output | No |
| Occupancy sensor | No |
| Connected (smart) capable | No |
Safety information
- Turn off power at the circuit breaker — not just the wall switch — before installing, removing or servicing the fixture, and confirm the circuit is dead with a non-contact voltage tester.
- Installation must comply with the National Electrical Code (NEC) or Canadian Electrical Code (CEC) and local codes. Many jurisdictions require a licensed electrician and a permit for new fixture locations or new wiring; if you are not comfortable with household wiring, hire one.
- Use only the junction box, housing, or mounting hardware specified in the installation instructions, and do not exceed the box-fill limits of the junction box.
- Install the fixture only on a circuit whose voltage matches the label, and never modify the LED driver or module.
- Connect dimmable fixtures only to dimmers the manufacturer lists as compatible, and keep the total connected LED load within the dimmer's LED rating (often much lower than its incandescent rating).
Installation and first-time setup
Recessed downlights mount above the ceiling, either in a new-construction housing fixed to joists before the drywall goes up or in a remodel housing that clips into a cutout in an existing ceiling. This model is a 9 in. fixture; use the cutout template from the manufacturer — never estimate the hole size.
- Plan the layout
Check for joists, ducts and pipes before cutting. As a starting point for general lighting, space fixtures about as far apart as the ceiling is high, and keep them about half that distance from walls; use closer spacing or more lumens for task areas.
- Turn off power
Switch off the breaker feeding the circuit and verify it is dead.
- Cut the opening
Trace the template and cut the opening with a drywall saw or hole saw. Keep the cut clean so the trim covers it fully.
- Wire the junction box
Feed the supply cable into the fixture's junction box through a cable clamp. Connect line to line, neutral to neutral and ground to ground with listed connectors, and close the box cover.
- Set options
Set the color-temperature selector before the fixture goes into the ceiling.
- Install the fixture
Push the housing or canless module into the opening until the mounting clips or springs grip the drywall and the trim sits flush.
- Restore power and test
Turn on the breaker and check operation through the full dimming range.
This fixture is damp-location rated, so it can be used in bathrooms, covered porches and similar areas with moisture but no direct water spray. Use a wet-location model where it will be hit by rain or shower spray.
Using your downlight
Dimming
The fixture dims continuously. Check the manufacturer's compatibility list: most LED drivers work best with trailing-edge (ELV) or LED-rated dimmers, and some dimmers have a low-end trim adjustment that stops flicker at the bottom of the range.
Choosing a color temperature
This fixture can be set to 2700K, 3000K, 3500K, 4000K, or 5000K. Set every fixture in a room to the same setting — mismatched color temperatures are very noticeable.
| Setting | Appearance | Typical use |
|---|---|---|
| 2700K | Warm white, similar to incandescent | Living rooms, bedrooms, dining areas |
| 3000K | Soft warm white, similar to halogen | Kitchens, living spaces, hospitality |
| 3500K | Neutral warm | Kitchens, retail, offices |
| 4000K | Neutral / cool white | Offices, laundry rooms, garages |
| 5000K | Cool white, daylight-like | Workshops, garages, task areas |
Light output and placement
At 1,480 lumens, this is a bright fixture for kitchens, work areas, commercial spaces and ceilings up to about 10–12 ft. LED fixtures reach full brightness instantly and are not shortened by frequent switching.
Care and maintenance
| When | What to do |
|---|---|
| Every 3–6 months | Dust the trim and lens with a soft, dry microfiber cloth with the light off and cool. Do not spray cleaner directly onto the fixture. |
| Every year | Check that the trim still sits flush and the springs or clips hold it firmly. A sagging trim can leave a gap that lets attic air leak. |
| When cleaning greasy kitchens | Wipe the lens with a cloth dampened in mild soapy water, then dry it. Avoid solvents and abrasive pads, which can cloud the lens. |
| Every year (outdoor/damp areas) | Look for insects, moisture or corrosion behind the trim and confirm any gaskets are intact. |
The integrated LEDs are not user-replaceable bulbs. The rated light-source life of 72,000 hours works out to roughly 66 years at 3 hours a day, or about 16 years at 12 hours a day. Over time the LEDs gradually dim rather than burning out; when output becomes too low, or if the driver fails, replace the fixture or LED module as the manufacturer directs.
Troubleshooting
Most downlight problems trace back to dimmer compatibility or wiring connections. Always turn off the breaker before opening the fixture or the junction box.
| Problem | Possible cause | What to try |
|---|---|---|
| Light does not turn on | Breaker off or tripped; loose wire connection; switch or dimmer failure. | Check the breaker; with power off, confirm connections in the junction box are tight; test with a standard switch. |
| Flickers or buzzes when dimmed | Dimmer not compatible with the LED driver; dimmer low-end trim set too low; too many or too few fixtures on the dimmer. | Use a dimmer on the manufacturer's compatibility list; adjust the dimmer's low-end trim; keep the load within the dimmer's LED rating. |
| Faint glow when switched off | Illuminated or smart switch leaking a small current; shared neutral wiring issue. | Try a standard switch; use a smart switch that has a neutral connection; have an electrician check the wiring. |
| Does not dim smoothly or turns off at low settings | Dimmer range not matched to the driver. | Raise the dimmer's minimum setting; consult the dimmer and fixture compatibility notes. |
| Color looks different from the other fixtures | Color-temperature selector set differently from neighboring fixtures. | Turn off power, check the selector setting and match it to the other fixtures. |
| Trim falls or hangs below the ceiling | Springs or clips not engaged; opening cut too large. | Reseat the springs in the receivers; use a trim with a wider flange or repair the drywall. |
| Turns off by itself after running a while | Driver overheating, often from insulation packed around a fixture or a loose connection. | Turn off power and check the installation. Do not cover Non-IC fixtures with insulation; call an electrician if the problem continues. |
| Moisture inside the lens | Gasket not seated; fixture exposed to more water than its rating allows. | Turn off power, dry the fixture and reseat the gasket; replace with a wet-rated fixture if needed. |
Energy use and running costs
The Adetu LBT-3/9XDPL-18 draws 18 W. Used 3 hours a day — a typical home assumption — it consumes about 19.7 kWh a year, roughly $3.35 per year at an electricity price of $0.17 per kWh. In a commercial space lit 12 hours a day, the same fixture uses about 79 kWh, or $13.40 a year.
Efficacy — lumens of light per watt of electricity — is the best single measure of a fixture's efficiency. This model delivers 82.2 lm/W. That figure is better than 19% of the 3,089 Recessed models in our database.
| Daily use | Energy per year | Cost per year |
|---|---|---|
| 1 hour | 6.6 kWh | $1.12 |
| 3 hours | 19.7 kWh | $3.35 |
| 6 hours | 39.4 kWh | $6.70 |
| 12 hours | 78.8 kWh | $13.40 |
The listed power factor is 0.92, high enough that the fixture draws current efficiently from the supply — useful in commercial buildings with many fixtures on one circuit.
Dimming reduces power roughly in proportion to light output.
Frequently asked questions
How bright is the Adetu LBT-3/9XDPL-18?
It is rated at 1,480 lumens while drawing 18 W, for an efficacy of 82.2 lumens per watt.
Is the Adetu LBT-3/9XDPL-18 dimmable?
Yes. It is continuously dimmable. Use a dimmer the manufacturer lists as compatible for flicker-free operation.
What color temperature is the Adetu LBT-3/9XDPL-18?
It is selectable between 2700K, 3000K, 3500K, 4000K, and 5000K. Set the selector before installation.
What size is the Adetu LBT-3/9XDPL-18?
Its nominal size is 9 in. Confirm the exact cutout or housing dimensions in the manufacturer's installation sheet before purchasing.
Can the Adetu LBT-3/9XDPL-18 touch insulation?
Yes. It is IC rated, which allows direct contact with thermal insulation.
Can I install the Adetu LBT-3/9XDPL-18 in a bathroom or shower?
It is damp-location rated, suitable for bathrooms away from direct shower spray. Use a wet-location fixture inside a shower.
How much does it cost to run the Adetu LBT-3/9XDPL-18?
At 3 hours a day and $0.17/kWh, it costs about $3.35 a year to operate.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified led downlights dataset published by the U.S. Environmental Protection Agency (record certified November 26, 2025), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with Adetu. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact Adetu or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.