LED DownlightsRetrofit Kit
Dals LEDPNLRTF56-CC- LED Downlight Manual
Setup, everyday use, maintenance and troubleshooting for the 6 in. LED downlight retrofit kit, with verified specifications.
- Light output820 lumens
- Power10 W
- Efficacy82 lm/W
- Color temp.2700K
About the Dals LEDPNLRTF56-CC-
This guide covers the Dals LEDPNLRTF56-CC-, a 6 in. LED downlight retrofit kit listed as ENERGY STAR certified. It produces 820 lumens from 10 W of input power, an efficacy of 82 lumens per watt.
Light quality: the fixture offers a 2700K color temperature (warm white) and a color rendering index of 92, which renders skin tones, wood and fabrics accurately.
Notable features include continuous dimming and a damp-location rating. The rated light-source life is 54,000 hours.
Specifications
| Brand | Dals |
|---|---|
| Model number | LEDPNLRTF56-CC-** |
| Model name / series | SSL Downlight retrofit |
| Fixture type | Retrofit Kit |
| Nominal size / aperture | 6 in. |
| Light output | 820 lumens |
| Input power | 10.0 W |
| Efficacy | 82.0 lm/W |
| Color temperature(s) | 2700K |
| Color rendering index (CRI) | 92 |
| Rated light-source life | 54,000 hours |
| Power factor | 0.99 |
| Continuously dimmable | Yes |
| Location rating | Damp location |
| Indoor / outdoor use | Indoor |
| Electrical connection | E26 screw-in adapter |
| Tunable / selectable white | Yes |
| Full-color tunable | No |
| Selectable light output | No |
| Occupancy sensor | No |
| Connected (smart) capable | No |
Safety information
- Turn off power at the circuit breaker — not just the wall switch — before installing, removing or servicing the fixture, and confirm the circuit is dead with a non-contact voltage tester.
- Installation must comply with the National Electrical Code (NEC) or Canadian Electrical Code (CEC) and local codes. Many jurisdictions require a licensed electrician and a permit for new fixture locations or new wiring; if you are not comfortable with household wiring, hire one.
- Use only the junction box, housing, or mounting hardware specified in the installation instructions, and do not exceed the box-fill limits of the junction box.
- Install the fixture only on a circuit whose voltage matches the label, and never modify the LED driver or module.
- Connect dimmable fixtures only to dimmers the manufacturer lists as compatible, and keep the total connected LED load within the dimmer's LED rating (often much lower than its incandescent rating).
Installation and first-time setup
A retrofit kit installs into an existing recessed housing (can) and replaces the old lamp and trim. This kit is sized for 6 in. housings; measure the inside diameter of your can before buying, because sizes are nominal.
- Turn off power
Switch off the breaker feeding the circuit and verify with a voltage tester. Let any old incandescent or halogen lamp cool before touching it.
- Remove the old lamp and trim
Unscrew the existing bulb, then pull down the old trim and unhook its springs or clips from the housing.
- Connect the adapter
Screw the kit's E26 adapter into the existing lamp socket, then plug the adapter lead into the connector on the LED module.
- Tuck in the leads
Fold the adapter lead and connectors up into the housing so they are not pinched by the trim.
- Attach and push up the trim
Fit the torsion springs into the housing's receivers or let the friction clips grip the can wall, then push the trim up until it sits flush with the ceiling.
- Restore power and test
Turn the breaker back on and test the fixture across the full dimmer range.
This fixture is damp-location rated, so it can be used in bathrooms, covered porches and similar areas with moisture but no direct water spray. Use a wet-location model where it will be hit by rain or shower spray.
Using your downlight
Dimming
The fixture dims continuously. Check the manufacturer's compatibility list: most LED drivers work best with trailing-edge (ELV) or LED-rated dimmers, and some dimmers have a low-end trim adjustment that stops flicker at the bottom of the range.
Light output and placement
At 820 lumens, this fixture is in the typical range for general lighting in kitchens, living areas and offices with 8–9 ft ceilings. LED fixtures reach full brightness instantly and are not shortened by frequent switching.
Care and maintenance
| When | What to do |
|---|---|
| Every 3–6 months | Dust the trim and lens with a soft, dry microfiber cloth with the light off and cool. Do not spray cleaner directly onto the fixture. |
| Every year | Check that the trim still sits flush and the springs or clips hold it firmly. A sagging trim can leave a gap that lets attic air leak. |
| When cleaning greasy kitchens | Wipe the lens with a cloth dampened in mild soapy water, then dry it. Avoid solvents and abrasive pads, which can cloud the lens. |
| Every year (outdoor/damp areas) | Look for insects, moisture or corrosion behind the trim and confirm any gaskets are intact. |
The integrated LEDs are not user-replaceable bulbs. The rated light-source life of 54,000 hours works out to roughly 49 years at 3 hours a day, or about 12 years at 12 hours a day. Over time the LEDs gradually dim rather than burning out; when output becomes too low, or if the driver fails, replace the fixture or LED module as the manufacturer directs.
Troubleshooting
Most downlight problems trace back to dimmer compatibility or wiring connections. Always turn off the breaker before opening the fixture or the junction box.
| Problem | Possible cause | What to try |
|---|---|---|
| Light does not turn on | Breaker off or tripped; loose wire connection; switch or dimmer failure. | Check the breaker; with power off, confirm connections in the junction box are tight; test with a standard switch. |
| Flickers or buzzes when dimmed | Dimmer not compatible with the LED driver; dimmer low-end trim set too low; too many or too few fixtures on the dimmer. | Use a dimmer on the manufacturer's compatibility list; adjust the dimmer's low-end trim; keep the load within the dimmer's LED rating. |
| Faint glow when switched off | Illuminated or smart switch leaking a small current; shared neutral wiring issue. | Try a standard switch; use a smart switch that has a neutral connection; have an electrician check the wiring. |
| Does not dim smoothly or turns off at low settings | Dimmer range not matched to the driver. | Raise the dimmer's minimum setting; consult the dimmer and fixture compatibility notes. |
| Color looks different from the other fixtures | Fixture has a different color temperature from neighboring fixtures. | Use fixtures with the same color temperature (this model is 2700K). |
| Trim falls or hangs below the ceiling | Springs or clips not engaged; opening cut too large. | Reseat the springs in the receivers; use a trim with a wider flange or repair the drywall. |
| Turns off by itself after running a while | Driver overheating, often from insulation packed around a fixture or a loose connection. | Turn off power and check the installation. Do not cover Non-IC fixtures with insulation; call an electrician if the problem continues. |
| Moisture inside the lens | Gasket not seated; fixture exposed to more water than its rating allows. | Turn off power, dry the fixture and reseat the gasket; replace with a wet-rated fixture if needed. |
Energy use and running costs
The Dals LEDPNLRTF56-CC- draws 10 W. Used 3 hours a day — a typical home assumption — it consumes about 11.0 kWh a year, roughly $1.86 per year at an electricity price of $0.17 per kWh. In a commercial space lit 12 hours a day, the same fixture uses about 44 kWh, or $7.45 a year.
Efficacy — lumens of light per watt of electricity — is the best single measure of a fixture's efficiency. This model delivers 82 lm/W.
| Daily use | Energy per year | Cost per year |
|---|---|---|
| 1 hour | 3.7 kWh | $0.62 |
| 3 hours | 11.0 kWh | $1.86 |
| 6 hours | 21.9 kWh | $3.72 |
| 12 hours | 43.8 kWh | $7.45 |
The listed power factor is 0.99, high enough that the fixture draws current efficiently from the supply — useful in commercial buildings with many fixtures on one circuit.
Dimming reduces power roughly in proportion to light output.
Frequently asked questions
How bright is the Dals LEDPNLRTF56-CC-?
It is rated at 820 lumens while drawing 10 W, for an efficacy of 82 lumens per watt.
Is the Dals LEDPNLRTF56-CC- dimmable?
Yes. It is continuously dimmable. Use a dimmer the manufacturer lists as compatible for flicker-free operation.
What color temperature is the Dals LEDPNLRTF56-CC-?
It is a 2700K fixture with a CRI of 92.
What size is the Dals LEDPNLRTF56-CC-?
Its nominal size is 6 in., meaning it is intended for recessed housings of that diameter. Confirm the exact cutout or housing dimensions in the manufacturer's installation sheet before purchasing.
Can I install the Dals LEDPNLRTF56-CC- in a bathroom or shower?
It is damp-location rated, suitable for bathrooms away from direct shower spray. Use a wet-location fixture inside a shower.
How much does it cost to run the Dals LEDPNLRTF56-CC-?
At 3 hours a day and $0.17/kWh, it costs about $1.86 a year to operate.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified led downlights dataset published by the U.S. Environmental Protection Agency (record certified February 13, 2025), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with Dals. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact Dals or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.