LED DownlightsPendant
RAB CD1016(CD34FA6SP-30-709-KC) LED Downlight Manual
Setup, everyday use, maintenance and troubleshooting for the 6 in. pendant LED downlight, with verified specifications.
- Light output3,150 lumens
- Power30 W
- Efficacy105 lm/W
- Color temp.4000K
About the RAB CD1016(CD34FA6SP-30-709-KC)
RAB model CD1016(CD34FA6SP-30-709-KC) is a 6 in. pendant LED downlight that meets ENERGY STAR requirements for light output, efficacy and color quality. It produces 3,150 lumens from 30 W of input power, an efficacy of 105 lumens per watt. That efficacy is better than 97% of the 39 Pendant models in our database.
Light quality: the fixture offers a 4000K color temperature (neutral white) and a color rendering index of 95, which renders skin tones, wood and fabrics accurately.
Notable features include continuous dimming and a wet-location rating. The rated light-source life is 102,000 hours.
Specifications
| Brand | RAB |
|---|---|
| Model number | CD1016(CD34FA6SP-30-709-KC) |
| Model name / series | LED Down light |
| Fixture type | Pendant |
| Nominal size / aperture | 6 in. |
| Light output | 3,150 lumens |
| Input power | 30.0 W |
| Efficacy | 105.0 lm/W |
| Color temperature(s) | 4000K |
| Color rendering index (CRI) | 95 |
| Rated light-source life | 102,000 hours |
| Power factor | 0.97 |
| Continuously dimmable | Yes |
| Location rating | Wet location |
| Indoor / outdoor use | Indoor |
| Tunable / selectable white | Yes |
| Full-color tunable | No |
| Selectable light output | No |
| Occupancy sensor | No |
| Connected (smart) capable | No |
Safety information
- Turn off power at the circuit breaker — not just the wall switch — before installing, removing or servicing the fixture, and confirm the circuit is dead with a non-contact voltage tester.
- Installation must comply with the National Electrical Code (NEC) or Canadian Electrical Code (CEC) and local codes. Many jurisdictions require a licensed electrician and a permit for new fixture locations or new wiring; if you are not comfortable with household wiring, hire one.
- Use only the junction box, housing, or mounting hardware specified in the installation instructions, and do not exceed the box-fill limits of the junction box.
- Install the fixture only on a circuit whose voltage matches the label, and never modify the LED driver or module.
- Connect dimmable fixtures only to dimmers the manufacturer lists as compatible, and keep the total connected LED load within the dimmer's LED rating (often much lower than its incandescent rating).
Installation and first-time setup
Pendant downlights hang from a canopy fastened to a ceiling junction box. The box must be rated to carry the fixture's weight; follow the instructions for setting the cord or stem length before final wiring.
- Turn off power
Switch off the breaker and verify the circuit is dead.
- Set the drop length
Adjust the cord, cable or stem to the hanging height you want. Over a table, the bottom of the fixture is commonly 30–36 in. above the surface.
- Mount and wire
Attach the crossbar to the box, connect line, neutral and ground with listed connectors, and secure the canopy.
- Restore power and test
Turn on the breaker and test the fixture.
Because this fixture is wet-location rated, it is suitable for locations exposed to water, such as covered porches, eaves and shower areas where the manual permits. Code requires fixtures within 3 ft horizontally and 8 ft vertically of a tub rim or shower threshold to be rated at least for damp locations — wet-location rated where subject to shower spray — and a GFCI-protected circuit is often required in these areas.
Using your downlight
Dimming
The fixture dims continuously. Check the manufacturer's compatibility list: most LED drivers work best with trailing-edge (ELV) or LED-rated dimmers, and some dimmers have a low-end trim adjustment that stops flicker at the bottom of the range.
Light output and placement
At 3,150 lumens, this is a high-output fixture suited to tall ceilings, lobbies, retail and other commercial spaces. LED fixtures reach full brightness instantly and are not shortened by frequent switching.
Care and maintenance
| When | What to do |
|---|---|
| Every 3–6 months | Dust the trim and lens with a soft, dry microfiber cloth with the light off and cool. Do not spray cleaner directly onto the fixture. |
| Every year | Check that the canopy and suspension are secure. |
| When cleaning greasy kitchens | Wipe the lens with a cloth dampened in mild soapy water, then dry it. Avoid solvents and abrasive pads, which can cloud the lens. |
| Every year (outdoor/damp areas) | Look for insects, moisture or corrosion behind the trim and confirm any gaskets are intact. |
The integrated LEDs are not user-replaceable bulbs. The rated light-source life of 102,000 hours works out to roughly 93 years at 3 hours a day, or about 23 years at 12 hours a day. Over time the LEDs gradually dim rather than burning out; when output becomes too low, or if the driver fails, replace the fixture or LED module as the manufacturer directs.
Troubleshooting
Most downlight problems trace back to dimmer compatibility or wiring connections. Always turn off the breaker before opening the fixture or the junction box.
| Problem | Possible cause | What to try |
|---|---|---|
| Light does not turn on | Breaker off or tripped; loose wire connection; switch or dimmer failure. | Check the breaker; with power off, confirm connections in the junction box are tight; test with a standard switch. |
| Flickers or buzzes when dimmed | Dimmer not compatible with the LED driver; dimmer low-end trim set too low; too many or too few fixtures on the dimmer. | Use a dimmer on the manufacturer's compatibility list; adjust the dimmer's low-end trim; keep the load within the dimmer's LED rating. |
| Faint glow when switched off | Illuminated or smart switch leaking a small current; shared neutral wiring issue. | Try a standard switch; use a smart switch that has a neutral connection; have an electrician check the wiring. |
| Does not dim smoothly or turns off at low settings | Dimmer range not matched to the driver. | Raise the dimmer's minimum setting; consult the dimmer and fixture compatibility notes. |
| Color looks different from the other fixtures | Fixture has a different color temperature from neighboring fixtures. | Use fixtures with the same color temperature (this model is 4000K). |
| Fixture pulls away from the ceiling | Mounting bracket loose; junction box not secured to framing. | Turn off power and tighten the bracket screws; have the box secured if it moves. |
| Turns off by itself after running a while | Driver overheating, often from insulation packed around a fixture or a loose connection. | Turn off power and check the installation. Do not cover Non-IC fixtures with insulation; call an electrician if the problem continues. |
| Moisture inside the lens | Gasket not seated; fixture exposed to more water than its rating allows. | Turn off power, dry the fixture and reseat the gasket; replace with a wet-rated fixture if needed. |
Energy use and running costs
The RAB CD1016(CD34FA6SP-30-709-KC) draws 30 W. Used 3 hours a day — a typical home assumption — it consumes about 32.9 kWh a year, roughly $5.58 per year at an electricity price of $0.17 per kWh. In a commercial space lit 12 hours a day, the same fixture uses about 131 kWh, or $22.34 a year.
Efficacy — lumens of light per watt of electricity — is the best single measure of a fixture's efficiency. This model delivers 105 lm/W. That figure is better than 97% of the 39 Pendant models in our database.
| Daily use | Energy per year | Cost per year |
|---|---|---|
| 1 hour | 11.0 kWh | $1.86 |
| 3 hours | 32.9 kWh | $5.58 |
| 6 hours | 65.7 kWh | $11.17 |
| 12 hours | 131.4 kWh | $22.34 |
The listed power factor is 0.97, high enough that the fixture draws current efficiently from the supply — useful in commercial buildings with many fixtures on one circuit.
Dimming reduces power roughly in proportion to light output.
Frequently asked questions
How bright is the RAB CD1016(CD34FA6SP-30-709-KC)?
It is rated at 3,150 lumens while drawing 30 W, for an efficacy of 105 lumens per watt.
Is the RAB CD1016(CD34FA6SP-30-709-KC) dimmable?
Yes. It is continuously dimmable. Use a dimmer the manufacturer lists as compatible for flicker-free operation.
What color temperature is the RAB CD1016(CD34FA6SP-30-709-KC)?
It is a 4000K fixture with a CRI of 95.
What size is the RAB CD1016(CD34FA6SP-30-709-KC)?
Its nominal size is 6 in. Confirm the exact cutout or housing dimensions in the manufacturer's installation sheet before purchasing.
Can I install the RAB CD1016(CD34FA6SP-30-709-KC) in a bathroom or shower?
It is wet-location rated, so it can be used where it may be exposed to water, including shower areas where the instructions permit. Follow local code for GFCI protection.
How much does it cost to run the RAB CD1016(CD34FA6SP-30-709-KC)?
At 3 hours a day and $0.17/kWh, it costs about $5.58 a year to operate.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified led downlights dataset published by the U.S. Environmental Protection Agency (record certified February 21, 2024), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with RAB. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact RAB or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.