ManualHarbor

PrintersPrinter

Epson C11CH25201 Printer Manual

Setup, everyday use, maintenance and troubleshooting for the 90 ipm printer, with verified specifications.

  • TypePrinter
  • Speed90 ipm
  • Sleep power0.98 W
  • Off-mode power0.1 W

About the Epson C11CH25201

The Epson C11CH25201 is a 90 ipm printer certified under the ENERGY STAR program for imaging equipment. The manufacturer markets it as the WF-110.

It is rated at 90 images per minute (ipm) in monochrome.

It draws 0.98 W in sleep and 0.1 W when switched off (standby). The factory default is to enter sleep 3 minutes after the last job.

Specifications

BrandEpson
Model numberC11CH25201
Model name / seriesWF-110
Product typePrinter
ENERGY STAR product categoryPrinters
Media size formatStandard
Rated monochrome speed90 ipm
Automatic duplex (two-sided)No
Professional imaging productNo
Sleep-mode power0.98 W
Standby (off) power0.10 W
Default delay to sleep3 min

Safety information

  • Plug the printer directly into a grounded wall outlet. Avoid light-duty extension cords, and replace a damaged power cord before use.
  • Keep the ventilation openings clear and leave the clearance around the unit that the manual specifies for paper trays, covers and service access.
  • Switch off and unplug the unit before cleaning it or reaching deep inside to clear a jam.

Setup

  1. Unpack and remove shipping materials

    Remove all tape, foam and protective film, including pieces inside the covers and paper trays.

  2. Choose a location

    Place the unit on a sturdy, level surface (or its floor stand) away from direct sunlight, heating vents and humid areas. Leave room to open covers and pull out trays.

  3. Load paper

    Fan the paper stack, adjust the tray guides to the paper size and load it below the fill line.

  4. Connect to your computer or network

    Connect the unit to your network (Ethernet or Wi-Fi where available) or directly by USB, following the setup guide. Network connection lets several users share it and makes firmware updates easier.

  5. Install drivers and software

    Add the printer in your operating system. Many current network printers work with driverless standards such as AirPrint, Mopria or IPP Everywhere; install the full manufacturer driver if you need finishing, security or accounting features.

  6. Check the sleep timer

    The unit is shipped to enter sleep 3 minutes after the last job. Keep this setting (or shorten it) to minimize idle energy use.

Using your printer

Sleep and power settings

The factory sleep delay is 3 minutes. In sleep the unit draws 0.98 W, and 0.1 W when switched off at the power button. Use the auto-off or weekly timer (if offered) to switch the unit off overnight and on weekends.

Care and maintenance

WhenWhat to do
Every 6 monthsInstall firmware updates from the manufacturer and vacuum dust from the exterior vents.

Troubleshooting

Most printer problems come from media, consumables, connections or settings. Try these steps first; for numbered error codes, look up the code in the manufacturer's manual or support site.

ProblemPossible causeWhat to try
Shows offline or jobs stay in the queueNetwork or IP address changed; wrong driver or port; printer asleep and not waking.Restart the printer and computer, print a network configuration page, re-add the printer using its current address, and reserve that address in your router.
Paper or media jamsWrong media for the tray; overfilled tray; worn rollers; debris in the path.Remove jammed media in the direction of the paper path, check for torn pieces, reload within the fill line, and clean the rollers.
Slow to start the first jobUnit waking from sleep.This is normal. Group jobs together; avoid disabling sleep, which raises energy use considerably.

Energy use and running costs

ENERGY STAR rates this device on its low-power modes: 0.98 W in sleep and 0.1 W when switched off. If it stays plugged in and asleep around the clock, sleep mode alone uses about 8.58 kWh per year — roughly $1.46 at $0.17 per kWh.

Switching it off outside a 10-hour, 5-day work week (and letting it sleep during working hours) cuts that to about 3.16 kWh per year ($0.54).

Energy used while actively printing is not included in these figures; it depends on how many pages you produce.

Frequently asked questions

What type of device is the Epson C11CH25201?

It is a 90 ipm printer in ENERGY STAR's standard media-size category. It is sold as the WF-110.

How fast is the Epson C11CH25201?

It is rated at 90 images per minute (ipm) in monochrome. Actual speed depends on the document, resolution and whether you print one- or two-sided.

How much power does the Epson C11CH25201 use in sleep?

It draws 0.98 W in sleep and 0.1 W when switched off. Left asleep all year, that is about 8.58 kWh, or $1.46.

How long does the Epson C11CH25201 take to go to sleep?

It is shipped with a default sleep delay of 3 minutes after the last job. You can change it in the control panel or web interface, but shorter delays save more energy.

Is the Epson C11CH25201 ENERGY STAR certified?

Yes. It appears on the ENERGY STAR certified imaging equipment list, with a certification date of June 2019.

Sources and disclaimer

Specifications on this page come from the ENERGY STAR certified printers dataset published by the U.S. Environmental Protection Agency (record certified June 16, 2019), retrieved October 7, 2026.

The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with Epson. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact Epson or an authorized service provider for warranty repairs and replacement parts.

Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.