PrintersWide-Format Printer
Mimaki TxF150-75 Printer Manual
Setup, everyday use, maintenance and troubleshooting for the 2 ipm wide-format color inkjet printer, with verified specifications.
- TypeWide-Format Printer
- Speed2 ipm
- Auto duplexNo
About the Mimaki TxF150-75
This guide covers the Mimaki TxF150-75, a 2 ipm wide-format color inkjet printer listed as ENERGY STAR certified.
It uses an inkjet imaging engine and is rated at 2 images per minute (ipm) in monochrome. As a large-format device, it handles wide media such as plans, posters or maps, typically on rolls.
Specifications
| Brand | Mimaki |
|---|---|
| Model number | TxF150-75 |
| Product type | Wide-Format Printer |
| ENERGY STAR product category | Printers |
| Marking technology | Inkjet |
| Media size format | Large |
| Color capable | Yes |
| Rated monochrome speed | 2 ipm |
| Automatic duplex (two-sided) | No |
| Professional imaging product | No |
| Remanufactured product | No |
| Standby (off) power | 0.00 W |
| Default delay to sleep | 5 min |
Safety information
- Plug the printer directly into a grounded wall outlet. Avoid light-duty extension cords, and replace a damaged power cord before use.
- Keep the ventilation openings clear and leave the clearance around the unit that the manual specifies for paper trays, covers and service access.
- Switch off and unplug the unit before cleaning it or reaching deep inside to clear a jam.
- Keep ink cartridges, bottles and waste-ink boxes away from children. If ink contacts skin, wash with soap and water; if it gets in the eyes, rinse with water and seek medical advice if irritation persists.
- Wide-format systems are heavy. Use two or more people, or the lifting equipment specified in the installation guide, and lock floor-standing casters once the unit is in place.
Setup
- Unpack and remove shipping materials
Remove all tape, foam and protective film, including pieces inside the covers and paper trays. Some models also have a printhead or carriage restraint; remove it as shown in the setup guide.
- Choose a location
Place the unit on a sturdy, level surface (or its floor stand) away from direct sunlight, heating vents and humid areas. Leave room to open covers and pull out trays.
- Install ink and printheads
Install the ink cartridges or fill the ink tanks with the bottles supplied, matching each color to its slot. The first start-up runs an ink-charging cycle that can take several minutes; do not turn the printer off during it. Setup ink partly fills the ink system, so the first set yields fewer pages than replacements.
- Load paper
Fan the paper stack, adjust the tray guides to the paper size and load it below the fill line. For roll media, mount the roll on the spindle and feed it until the printer detects it, then enter the media type in the control panel.
- Connect to your computer or network
Connect the unit to your network (Ethernet or Wi-Fi where available) or directly by USB, following the setup guide. Network connection lets several users share it and makes firmware updates easier.
- Install drivers and software
Add the printer in your operating system. Many current network printers work with driverless standards such as AirPrint, Mopria or IPP Everywhere; install the full manufacturer driver if you need finishing, security or accounting features.
- Check the sleep timer
The unit is shipped to enter sleep 5 minutes after the last job. Keep this setting (or shorten it) to minimize idle energy use.
Using your printer
Printing
- Choose grayscale in the print dialog for drafts and text-only pages to save color toner or ink.
- Use draft or standard quality for everyday documents; reserve best or photo quality for photos on matching paper.
- Select the correct paper type and size in the driver so the printer applies the right heat or ink density.
- Print at least once a week to keep the nozzles from drying out.
Sleep and power settings
The factory sleep delay is 5 minutes. Turn the printer off with its power button rather than a power strip, so the printhead is capped and does not dry out.
Care and maintenance
| When | What to do |
|---|---|
| Weekly | Print a page (or run a nozzle check) to keep ink flowing. |
| When print shows streaks | Run a nozzle check, then a head cleaning only if needed — cleaning cycles consume ink. Wait several hours between repeated cleanings. |
| When prompted | Replace ink cartridges, refill tanks with genuine bottles of the correct type, and replace the maintenance box (waste-ink pad) when the printer asks. |
| Every 6 months | Install firmware updates from the manufacturer and vacuum dust from the exterior vents. |
Troubleshooting
Most printer problems come from media, consumables, connections or settings. Try these steps first; for numbered error codes, look up the code in the manufacturer's manual or support site.
| Problem | Possible cause | What to try |
|---|---|---|
| Shows offline or jobs stay in the queue | Network or IP address changed; wrong driver or port; printer asleep and not waking. | Restart the printer and computer, print a network configuration page, re-add the printer using its current address, and reserve that address in your router. |
| Streaks, banding or missing colors | Clogged nozzles; printhead misaligned; low ink. | Run a nozzle check and, if needed, a head cleaning; then align the printhead and check ink levels. |
| Cartridge not recognized | Protective tape left on; contacts dirty; incompatible cartridge. | Remove the tape, reseat the cartridge, wipe contacts with a dry lint-free cloth, and use the cartridge type specified for this model. |
| Smudged or wet prints | Paper type setting wrong; printing on the wrong side of photo paper. | Select the correct paper type and load photo paper glossy side toward the printhead as shown on the tray. |
| Paper or media jams | Wrong media for the tray; overfilled tray; worn rollers; debris in the path. | Remove jammed media in the direction of the paper path, check for torn pieces, reload within the fill line, and clean the rollers. |
| Slow to start the first job | Unit waking from sleep. | This is normal. Group jobs together; avoid disabling sleep, which raises energy use considerably. |
Frequently asked questions
What type of device is the Mimaki TxF150-75?
It is a 2 ipm wide-format color inkjet printer in ENERGY STAR's large media-size category.
How fast is the Mimaki TxF150-75?
It is rated at 2 images per minute (ipm) in monochrome. Actual speed depends on the document, resolution and whether you print one- or two-sided.
Does the Mimaki TxF150-75 print on both sides automatically?
No. The certification record does not list automatic duplex printing; you can still print two-sided manually by reloading the pages.
Does the Mimaki TxF150-75 print in color?
Yes. It is listed as color capable.
How long does the Mimaki TxF150-75 take to go to sleep?
It is shipped with a default sleep delay of 5 minutes after the last job. You can change it in the control panel or web interface, but shorter delays save more energy.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified printers dataset published by the U.S. Environmental Protection Agency (record certified November 16, 2022), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with Mimaki. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact Mimaki or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.