Room Air ConditionersThrough-the-Wall
DuraSTAR DRTAC102XVB1 Room Air Conditioner Manual
Setup, everyday use, maintenance and troubleshooting for the 10,000 BTU/h through-the-wall air conditioner, with verified specifications.
- Cooling capacity10,000 BTU/h
- CEER14.1
- Power supply230/208 V
- Est. yearly cost$90.42
About the DuraSTAR DRTAC102XVB1
This guide covers the DuraSTAR DRTAC102XVB1, a 10,000 BTU/h through-the-wall air conditioner on the ENERGY STAR certified list. ENERGY STAR's sizing chart matches this capacity to a room of roughly 400–450 sq. ft.
It is designed for a permanent wall sleeve rather than a window opening; the cabinet measures 24.1 in. wide, 14.7 in. high and 20.9 in. deep and weighs 56.2 lb (25.5 kg).
Key equipment includes a variable-speed (inverter) compressor, a 230/208 V dual-voltage power supply that needs a dedicated 230 V or 208 V circuit, and R-32 refrigerant (global warming potential 675).
Its combined energy efficiency ratio (CEER) is 14.1, and it uses 47% less energy than the U.S. federal standard for its product class. That CEER is higher than 56% of the 65 Through-the-Wall models in our database.
Specifications
| Brand | DuraSTAR |
|---|---|
| Model number | DRTAC102XVB1 |
| Installation type | Through-the-Wall |
| Cooling capacity | 10,000 BTU/h |
| Combined energy efficiency ratio (CEER) | 14.1 |
| Annual energy use | 532 kWh/yr |
| Better than federal standard | 47% |
| Rated voltage | 230 V |
| Dual voltage (230/208 V) | Yes |
| Heating mode (reverse cycle) | No |
| Window mounting style | Does Not Straddle Window or Windowsill |
| Support bracket | No |
| Variable-speed compressor | Yes |
| Width | 24.1 in. |
| Height | 14.7 in. |
| Depth | 20.9 in. |
| Weight | 56.2 lb |
| Refrigerant | R-32 |
| Refrigerant global warming potential (GWP) | 675 |
| Smart / connected features | No |
| DOE product class | 8a. Without reverse cycle, without louvered sides, and 8,000 to 10,999 Btu/h |
| ENERGY STAR Most Efficient | No |
Safety information
- This is a 230/208 V dual-voltage appliance. Plug it only into a properly grounded, dedicated receptacle of the matching voltage and plug configuration, installed by a licensed electrician.
- The power cord carries a leakage-current or arc-fault safety device (the plug with TEST and RESET buttons). Test it before each cooling season and do not use the unit if the device will not reset.
- Unplug the air conditioner before cleaning, removing the front grille or doing any maintenance.
- The unit weighs 56.2 lb (25.5 kg). Use two people to lift it and keep a firm grip on the cabinet until it is fully secured — a falling air conditioner can cause serious injury.
- Never let children play with or climb on the unit, and keep the outdoor grille free of debris, nests and snow.
- Do not block the indoor or outdoor air openings, and never insert objects through the grilles while the fan is running.
Installation and first-time setup
Before installing, confirm the opening and the space around it. The cabinet is 24.1 in. wide, 14.7 in. high and 20.9 in. deep. Wall-sleeve dimensions are not part of the certification data, so confirm the required sleeve with the manufacturer before installation.
- Check the wall sleeve
Through-the-wall units slide into a metal sleeve built into the exterior wall. Confirm the sleeve dimensions and brand compatibility with the manufacturer's specification before purchase — chassis and sleeves from different manufacturers are often not interchangeable. Because this model has no side louvers, it exhausts heat only through the rear grille and must not be installed in an ordinary window opening.
- Prepare the opening
For a new installation, the wall opening must be framed with a header like a window, and the sleeve sealed and flashed against water entry. Cutting into a load-bearing or exterior wall is a job for a qualified contractor.
- Install the rear grille
Fit the outdoor grille that matches the sleeve and chassis so the condenser can reject heat properly. A mismatched or blocked grille causes high head pressure and poor cooling.
- Slide in the chassis
With two people, slide the chassis fully into the sleeve, seal the gap with the supplied gasket or trim, and fasten it as the instructions describe.
- Connect power
Plug into the dedicated 230 V or 208 V receptacle. If no matching receptacle exists, have an electrician install one; never modify the plug.
- First start-up
If the unit was tipped on its side during transport, leave it upright for the time the manual specifies before starting it so compressor oil can settle. Then run Cool mode at the lowest temperature setting for 15 minutes and check that air leaving the front is noticeably colder than room air.
Using your air conditioner
Choosing a mode and temperature
Use Cool for normal operation and Fan only to circulate air without cooling. For comfort with lower bills, set the thermostat to about 78 °F (26 °C) when the room is occupied; each degree warmer reduces running time. Most models also offer an energy-saver setting that cycles the fan off with the compressor — use it when steady airflow is not needed. Because the unit also removes moisture as it cools, the room usually feels comfortable at a higher setpoint than you might expect.
How the variable-speed compressor behaves
This model uses a variable-speed (inverter) compressor. Instead of switching hard on and off, it slows down as the room approaches the setpoint and keeps running quietly at low speed. Long, steady run times are normal and are where most of the energy savings come from. Avoid setting the thermostat far below the desired temperature — it will not cool faster, it will only run at full speed longer.
Getting even cooling
- Keep furniture and curtains at least a couple of feet clear of the front grille so the cold airstream can reach the room.
- Aim the louvers upward and toward the center of the room — cool air sinks and spreads on its own.
- Close doors to unused rooms and draw blinds on sunny windows during the hottest part of the day.
- Run a ceiling fan on low alongside the air conditioner to raise the comfortable setpoint by a few degrees.
- Turn the unit off or raise the setpoint when the room is empty; a timer or schedule (if your model has one) makes this automatic.
Care and maintenance
| When | What to do |
|---|---|
| Every 2 weeks of use | Remove and wash the front air filter in warm water with mild detergent; let it dry completely before reinstalling. A clogged filter cuts airflow and can cause the coil to ice up. |
| Every month | Wipe the front grille and louvers with a damp cloth. Check that condensate is draining outdoors and not dripping indoors. |
| Start of each season | Test the TEST/RESET safety plug, inspect the cord for damage, and confirm the sleeve seal and rear grille are intact. |
| Every year | With the unit unplugged, gently vacuum dust from the indoor coil fins with a soft brush. Have the outdoor coil cleaned if it is matted with debris; straighten bent fins with a fin comb. |
| End of season | Clean the filter, run Fan mode for a few hours to dry the interior, and fit an insulated cover over the indoor face to cut drafts. Never cover the unit while it is running. |
Troubleshooting
Most room air conditioner problems trace back to airflow, installation or power. Work through these checks before calling for service. If the display shows an error code, look it up in the code table of your manufacturer's manual.
| Problem | Possible cause | What to try |
|---|---|---|
| Unit will not start | Safety plug tripped; breaker off; unit just turned off and restarting. | Press RESET on the plug; check the breaker; wait about 3 minutes — compressors have a restart delay to protect themselves. |
| Not cooling enough | Dirty filter; setpoint too high; unit undersized for the room; gaps around the installation. | Clean the filter; lower the setpoint; seal side panels and sash gaps; compare the room size with the 10,000 BTU/h rating and the sizing chart. |
| Ice or frost on the coil | Restricted airflow; very cool outdoor temperatures; fan speed too low. | Switch to Fan only until the ice melts, clean the filter, raise the fan speed, and avoid cooling when it is cool outside. |
| Water dripping indoors | Incorrect slope; blocked drain path; unit not level side to side. | Recheck the installation slope against the manual and clear debris from the base pan. |
| Runs in short bursts | Unit oversized for the space; thermostat sensor in the cold airstream. | Use a lower fan speed or energy-saver mode; an oversized unit cools quickly but leaves the room clammy. |
| Rattling or vibration | Loose side panels or brackets; window sash not seated; debris in the fan. | Tighten fasteners, seat the sash firmly, and with the unit unplugged check for objects touching the fan blades. |
| Gurgling or water sounds | Condensate being picked up by the fan slinger ring to cool the coil. | This is normal on many window units and improves efficiency. |
Energy use and running costs
The DuraSTAR DRTAC102XVB1 is rated at 531.9 kWh per year. That figure assumes 750 hours of cooling per year, the DOE and ENERGY STAR usage assumption for room air conditioners. At an average electricity price of $0.17 per kWh, that works out to about $90.42 per cooling season.
While the compressor is running, expect a draw of roughly 709 W, or about $0.12 per hour at $0.17/kWh. Running it 8 hours a day for a 90-day summer would use about 511 kWh ($86.81).
Because it uses 47% less energy than the federal standard, a minimum-efficiency unit of the same class would use roughly 1,004 kWh under the same assumptions. The difference — about 472 kWh — is worth around $80.19 a year, or $802 over a typical 10-year life.
Your actual cost depends on climate, how many hours the unit runs, the thermostat setting, sun exposure and how well the installation is sealed.
Frequently asked questions
What size room will the DuraSTAR DRTAC102XVB1 cool?
With 10,000 BTU/h of cooling capacity, ENERGY STAR's sizing chart puts it at roughly 400–450 sq. ft. Reduce capacity needs by about 10% for a heavily shaded room, add about 10% for a very sunny one, add 600 BTU/h for each regular occupant beyond two, and add 4,000 BTU/h if the unit cools a kitchen.
Does the DuraSTAR DRTAC102XVB1 plug into a regular outlet?
No. It is rated for 230/208 V (dual voltage) and needs a dedicated 230 V or 208 V receptacle that matches its plug, not a standard 115 V outlet.
Can the DuraSTAR DRTAC102XVB1 heat as well as cool?
No. The certified configuration is cooling-only; it has no reverse-cycle heating mode.
How much does it cost to run the DuraSTAR DRTAC102XVB1?
It is rated at 532 kWh per year based on 750 hours of use, about $90.42 a year at $0.17/kWh. That is roughly $0.12 per hour of compressor operation.
What is the CEER rating of the DuraSTAR DRTAC102XVB1?
Its combined energy efficiency ratio is 14.1. CEER is BTU/h of cooling divided by watts of power, with standby and off-mode power folded in, so a higher number means lower operating cost. Under the DOE test it uses 47% less energy than the federal standard for its class.
What are the dimensions of the DuraSTAR DRTAC102XVB1?
The cabinet is 24.1 in. wide, 14.7 in. high and 20.9 in. deep, and the unit weighs 56.2 lb. As a through-the-wall model, it must match the wall sleeve specified by the manufacturer.
What refrigerant does the DuraSTAR DRTAC102XVB1 use?
The certification record lists R-32, which has a global warming potential (GWP) of 675. R-32 is classed as mildly flammable (A2L), so sealed-system service must be done by a qualified technician.
Sources and disclaimer
Specifications on this page come from the ENERGY STAR certified room air conditioners dataset published by the U.S. Environmental Protection Agency (record certified September 28, 2026), retrieved October 7, 2026.
The setup, operating, maintenance and troubleshooting guidance is written by ManualHarbor's editors for this specific product type and configuration. It is an independent guide — not a reproduction of the manufacturer's manual — and ManualHarbor is not affiliated with DuraSTAR. Always follow the safety instructions, installation requirements and warranty terms supplied with your unit, and contact DuraSTAR or an authorized service provider for warranty repairs and replacement parts.
Running-cost figures use assumed U.S. average utility prices and are estimates for comparison only. See our editorial methodology for details.
Report a problem with this guide
Spotted a wrong value, a broken link or something unclear? Tell us and we will review it.